7 Tips on Troubleshooting Residential Tanning Beds

by Denise R. Morey

Troubleshooting Residential Tanning Beds

Introduction

Investing in a residential tanning bed comes with the responsibility of troubleshooting. While the investment is a well-calculated move to avoid spending too much money, it needs care. Otherwise Troubleshooting Residential Tanning Beds should be on your list of factors. If you leave out this aspect, the lifespan of your bed reduces. In some cases, this is how you can even lose out on warranty claims.

When Troubleshooting Residential Tanning Beds under your care, always know your limits. There are some technical aspects that you cannot do on your own. But most of the problems are small issues which you can work out on your own. This saves time and money in the process. Below are some tips you can bank on when Troubleshooting Residential Tanning Beds.

Tanning bed fails to turn on

This is a very common fault for new beds. If you bought your tanning bed and it is your first time using it, there are possible causes. The most obvious one is that there is no power coming to the entire bed. Check if you have plugged in the socket.

Some plugs have fuses meant to protect the bed. Check if such fuses are still intact. If you check and everything is fine, then check the wires leading to the bed. Troubleshooting Residential Tanning Beds is a skill that requires patience. You cannot afford to rush any aspect.

Finally, always try to check for the obvious. Ensure that you have turned on the switch. You can also verify that you have plugged the equipment in the right outlet with the correct output.

Tanning lamps fail to turn on

This is one of the commonest issues when Troubleshooting Residential Tanning Beds. To start with, check the tanning lamps. They could be faulty. But the probability of many turning lamps failing at the same time is small. That is why you may need to look a bit further. check the bulb holders to make sure they are in good condition. If they are fine, then it is time to look at the ballasts.

If all the inspections reveal no faulty end, then the supply is not working. Check the cables leading to the lamps. One of them could be loose or there could be a broken line feeding the lamps. The procedure of Troubleshooting Residential Tanning Beds needs an open mind. Do not make assumptions before you verify.

One tanning lamp or a few of them fail to turn on

When a single tanning lamp fails to turn on, it means that the problem is local. Check the lamp because it could be faulty. If the failing lamp is fine, check that single lamp holder. Then you can follow up with its ballast. If all is fine, then check the cable powering that lamp. Look out for any loose or broken connections. You can apply the same procedure to the small group of three or more lamps if they have failed.

The tanning bed is heating up

You need to note that Troubleshooting Residential Tanning Beds sometimes works with experience. But it should not be the only basis. A heating-up tanning bed calls for you to check if the fans are working well. If all is fine in this area, turn to the ventilation side of things. check the vent holes. See to it that they have no blockages.

Tanning bed is overloading the supply

If you notice that the breaker trips the moment you switch on the bed, then there is an overload. Check to ensure that there are no naked cables touching or any possible short circuit. Try Troubleshooting Residential Tanning Beds with this issue by looking in other areas. It could be that you have plugged the equipment into a socket outlet will a low rating. If the voltage rating for your bed is 230 VAC, then it will not work with 120 VAC. But around 220 VAC or 210, it may work. In some cases, you may also need to check the circuit breaker itself.

Lamps turn on in a slow manner

The first suspicion, in this case, could be that the lamp is not receiving enough power. Troubleshooting Residential Tanning Beds should also help you to check the voltage. Check and ensure that you have selected the right voltage for your lamp. If you have plugged your tanning bed in a lower voltage output source, this can happen.

Cracked acrylics

This is very easy to see even from the earliest stages. Troubleshooting Residential Tanning Beds with cracks can tell a story. Possible physical damage caused by objects falling on it or placed on top of it can cause this. Ensure that very heavy objects are not put on it. During cleaning, only use the correct cleaning agents for acrylics. Products used for cleaning windows and fabrics may not work here. Always stick to the manufacturer’s recommended products.

Conclusion

Troubleshooting Residential Tanning Beds is not rocket science. It is a task you can manage and cut down on frequent calls to the technician or electrician. But the best shot you can have at this is a good maintenance routine. This should be the one spelled out by the manufacturer. A good cleaning routine and physical inspection are never missed in those recommendations. Follow every aspect and make sure you stick to the stipulated schedules.

There are other aspects that end up being too technical. For example, resetting the timer or verifying if a relay is working. These and other related technical procedures need a qualified technician. Your Troubleshooting Residential Tanning Beds ends with small issues. Leave the complicated stuff to the trained hands with skill, certification, and knowledge.

Before buying the tanning bed, you may find the expense too high in some cases. The high cost reduces the burden of Troubleshooting Residential Tanning Beds. This high capital expenditure works for you in the long run. It is better than buying it at a low cost, then you end up spending too much on repairs.

Related Posts

Leave a Comment

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More

Privacy & Cookies Policy